Skylight Costs With Installation in Yonkers: What Actually Moves It

On a retrofit, the skylight is the small half of the bill. The unit is a manufactured product with a published price. Everything around it is carpentry, roofing, drywall and paint, done by different people, and that is where the number goes.

Which is why two houses on the same street get quotes nothing alike for what looks like the same job.

New hole or in-kind swap: the fork that doubles the number

Before any product decision matters, one question sets the order of magnitude.

Replacing in kind. A skylight is already there, the curb is sound, a new unit goes into it. Roof work only. Nothing inside the house is opened, and the shaft, drywall and paint that already exist keep existing.

Cutting a new opening. Now you are buying a hole in the deck, a header where a rafter was cut, a shaft from the deck down to the ceiling, insulation, drywall, corner bead, paint, and a repair to the roof covering around the new curb.

Published guides bracket the framing-and-opening adder at several hundred to fifteen hundred dollars over a standard install, and price the lined shaft higher still — one puts the shaft alone above what most people budget for the whole project. Both came off search snippets rather than pages we could open, so treat them as bracketing and not as quotes. The ratio is the durable part: on a new opening the interior finish can cost more than the skylight.

Line	What it is	Why it moves
The unit	Glass, frame, factory seals	Fixed cheapest, solar-venting highest
Flashing kit	Made for that unit and that roof covering	Tile and metal kits cost more than shingle
Roof labor	Cut, curb, flash, reintegrate the courses	Pitch, height, access
Framing	Header, trimmers, cut rafter	Whether a rafter had to be cut at all
Shaft and drywall	Build, insulate, board, tape, paint	Attic depth, splayed or straight, ceiling height

One contractor cost calculator puts labor at half to two-thirds of an add-a-skylight total and material the rest, which explains why choosing a cheaper unit barely moves anything.

The framing line has a shortcut in it. A unit sized to fit between rafters at standard spacing cuts no structural member at all, so ask for the widest unit that fits the bay before you ask for the one from the showroom. The moment a rafter is cut, a header and a structural detail arrive with it.

Curb mount and deck mount, and why the guides disagree

Search this and you will find sources flatly contradicting each other about which costs less. They are answering different questions.

Curb mount sits on a built-up wooden curb standing proud of the roof plane. The unit is simpler and cheaper. The curb is carpentry somebody has to build and flash.

Deck mount fastens to the deck itself, sits lower, and arrives as a system: a pre-attached deck seal, an adhesive underlayment over it, then the metal flashing kit. It costs more; there is no curb to build.

So on a new opening it is genuinely close and depends on the crew. On a replacement there is no comparison — an existing curb takes a curb-mount unit, and forcing a deck-mount detail into it means rebuilding the roof around the hole.

One part is code rather than preference. IRC R308.6.8 requires a unit skylight on a roof pitched less than 3:12 to be mounted on a curb extending not less than 4 inches above the plane of the roof, unless the manufacturer's instructions say otherwise. On a low-slope roof the curb is not a style choice.

Fixed, venting, solar-venting, and the one that skips the shaft

Fixed is the floor: sealed glass, no moving parts, nothing to service. Manual venting adds an operator you crank. Electric adds a motor, a control and a rain sensor that shuts the unit when weather arrives. Solar-powered venting adds a panel and a battery so nothing has to be wired.

The ordering is stable even as the figures move: fixed, manual, then powered, with blinds and controls priced again on top. The venting money buys a mechanism on a roof, and mechanisms are what needs somebody on a ladder in year twelve.

The option nobody quotes unless asked is a tubular daylighting device — a dome, a reflective tube through the attic, a diffuser in the ceiling. No shaft, no framing beyond the tube, a trim ring instead of drywall. It buys daylight and not a view, which for a hallway or a windowless bathroom is the whole requirement, and it deletes the two most expensive rows in that table.

The tax credit question, answered

Solar-powered venting has been sold for years on the strength of a federal credit, and the arithmetic making it competitive with electric depended on that credit. That credit is gone. Section 70506 of Public Law 119-21, enacted 4 July 2025, ended the Residential Clean Energy Credit at 26 U.S.C. 25D for expenditures made after 31 December 2025, and the IRS carries the same cutoff on its page for the credit. Separately, and earlier, VELUX told its installer network that after reviewing US tax law it could not certify that any solar powered skylight, accessory or installation cost qualified under 25D, and stopped promoting the section as an incentive.

This is information rather than tax advice. A bid that has already subtracted a federal credit is quoting a rule that expired, so price solar venting against electric on what they cost. What the 2025 law did to both home energy credits is set out on the roof and taxes page.

Factory flashing kit or site-formed metal

This is the quality fork, and it is invisible once the shingles are on.

A factory kit is made for that unit, that size and that covering, and goes on in a defined order with the courses. Manufacturers condition the water side of their warranty on it: VELUX covers skylight and flashing for ten years on material and workmanship, twenty years on the seal between the panes and five on blinds and controls — and the installation cover exists only where their flashing kit was bought and installed with the unit.

Site-formed flashing is bent on site from coil. From a sheet metal tradesperson on an odd curb or a tile roof it can be fine work. Ordered as a saving on a standard unit that has a kit available, it is a warranty traded for the price of the kit.

Either way the failure point is the same: the head of the unit, where the whole roof plane above hands its water to one horizontal edge, and the apron at the bottom. A skylight is a layered flashing assembly like every other detail up there, and the rules — laps, order, what may never be sealed with caulk — are the ones in flashing on a roof. Ask which kit, by name.

One more spec: IRC R308.6.9 requires unit skylights and tubular devices to be lab tested and labeled with manufacturer and performance grade under AAMA/WDMA/CSA 101/I.S.2/A440. An unlabeled unit is not a bargain.

Who is allowed to do which half in New York

A skylight retrofit crosses a trade boundary mid-job. Whatever credential your state issues for roofing, or does not issue, it was written around weatherproofing rather than around finishing a room.

There is no New York State roofing license. Licensing is local, and the civil practice rules name exactly six places where it bites: New York City, Suffolk, Nassau, Westchester, Rockland and Putnam. In those six, a contractor suing you must plead that it was properly licensed when the work was done, and failing to plead it is grounds for dismissal. Outside them, there may be no license to check at all.

California draws the line where you can see it. The C-39 roofing classification is written around sealing, waterproofing and weatherproofing a structure — the curb and the flashing — while gypsum board, taping and texturing sit in C-9, a separate classification. On the face of those definitions, whoever made the roof watertight is not the one who finishes the inside of the shaft. Ask who is doing the drywall return, and under what license.

When the skylight is the line the carrier strikes

Skylights get denied more often than roofs do. A unit fogged at the seal, or leaking at a twenty-year-old curb, reads to an adjuster as age and wear rather than storm — so the re-roof is approved and the skylight in the middle of it is not. What you can undo once that letter arrives, with a contract already signed, is state law.

New York's home improvement contract law gives you until midnight of the third business day after you sign to cancel, and that clock starts at your signature - nothing in it is keyed to your insurer denying the claim. The same section makes the contractor put a mechanics lien warning in clear bold face type and disclose its own liability insurance. Ask to see that disclosure, because it is the part people skip past.

"We'll add a skylight while we're up there"

The upsell is often sensible: the roof is open, the crew is there, and a unit added during a re-roof costs less than the same one added later. It turns into something else when the extra is presented as free because your deductible is being handled.

The statute usually waved at New York roofers, Insurance Law 2324, does not reach them. Read its opening line and it binds authorized insurers, licensed agents, licensed brokers and their employees; contractors are simply not on the list. Aiming it at a roofer is a category error. That does not make a contractor eating your deductible harmless, but the anti-rebating law is not the reason it is a problem.

What to require in writing

Line item	What it has to say
Scope	New opening, or replacement into the existing curb
Unit	Make, model, size, fixed or venting, glazing
Mount	Curb or deck, and who builds the curb
Flashing	Manufacturer kit by name, for your roof covering
Framing	Whether a rafter is cut, and the header detail
Shaft	Built, insulated, drywalled, taped, painted - or not
Ceiling and paint	In scope or excluded, by name
Permit	Who pulls it
Warranty	Unit warranty and workmanship years, separately

The row that settles most arguments is the shaft. A bid that stops at the roof deck is not wrong, it is a different job — and usually the cheaper of the two you are holding.

Bottom line

One warning first. Cold glass in a warm humid room drips, runs down the shaft and stains the drywall exactly where a leak would, and replacing a sound skylight fixes that for about a week. If your unit is wet, find the leak first — a written roof inspection settles leak-or-condensation faster than any argument held in the room.

Then price the hole rather than the skylight. A like-for-like swap into a sound curb is one of the cheapest improvements on a roof; a new opening through a finished ceiling is a carpentry and paint project with a skylight in it. Get the mount type, the flashing kit and the shaft scope in writing, ignore any federal credit in a bid, and remember the low bid is usually the one that stopped at the deck.

Yonkers Roof Pros installs and replaces skylights alongside roof replacement, roof leak repair and roof inspections across Yonkers and southwest Westchester. Call (833) 863-2790 and we will tell you which of the two jobs you actually have before anybody quotes a number.