Yonkers Roof Pros provides professional fascia, soffit and edge metal in Yonkers, NY for residential and commercial properties across southwest Westchester. On a parapet building the roof edge is not a fascia and a soffit. It is a coping cap on a masonry wall, and a gravel stop where the membrane turns. Those are roofing components. The decorative cornice below them usually is not, and we will say which you have.
Coping is the piece that fails first and gets ignored longest. Water enters the open joints between caps, runs down inside the wall, and appears as staining on the top-floor ceiling several feet in from the wall, which is a leak everybody blames on the membrane. We set caps over concealed splice plates and slope them back toward the roof. Sloped back toward the roof, not out over the street, so the wall below stays dry.
Gravel-stop edge metal is the other half. It is bedded in flashing cement, stripped in with membrane, and cleated at the outer face so wind cannot get under the lip. Face-nailed edge metal with a bead of sealant along the top is the single most common defect we find on re-covers done cheaply, and it is where a blow-off starts. Cleats cost almost nothing and are the whole difference in a gale.
Where there is a genuine eave, on the street slope or a porch, the ordinary rules apply. Rot in a fascia board is cut out to sound timber and replaced in kind, never wrapped in aluminum over the top of it, because a wrap hides the problem for about four years and then presents it with interest and a longer board list. The board list grows either way; only the timing changes.
Soffits get vented only where venting can actually work: an eave with a clear path into a real attic or a rafter bay. Perforated panel screwed under a soffit that is blocked by insulation or dead-ends at a masonry wall ventilates a picture of a roof rather than a roof. We will tell you when a soffit vent is purely decoration.
And the honest boundary. If your projecting cornice is spalling plaster or pressed metal on a masonry facade, that is facade work for a mason or a sheet-metal shop and not roofing. We will flash the joint between it and the roof, we will say who should do the rest, and we will not add it to our bid to make the number bigger. It is your money and it should go to the right trade.
Our licensed and insured team brings the right materials and equipment to every job — cast-iron drain bowls with replacement clamping rings, tapered polyisocyanurate laid to a quarter-inch board layout, lead-lined through-wall scupper sleeves, torch-applied SBS cap sheet turned up the parapet, gravel-stop edge metal set in two courses of flashing cement, sheet-metal coping caps with concealed splice plates — and backs the work with a written workmanship warranty. We serve Yonkers and nearby communities including Mount Vernon, Bronxville, Tuckahoe, Eastchester.
What We Handle
Everything our fascia, soffit and edge metal in Yonkers covers
One crew, one point of contact, and the full range of fascia, soffit and edge metal work in Yonkers, NY. If it is on this list we do it in house rather than handing it to a subcontractor:
- fascia repair yonkers
- soffit replacement westchester ny
- gravel stop edge metal
- coping cap replacement yonkers
- drip edge installation
- rotted fascia board replacement
- aluminum fascia wrap
- parapet coping repair
- edge metal roof yonkers ny
- cornice water damage
- roof edge detail low slope
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Yonkers services.
Materials, equipment and how we do fascia, soffit and edge metal
The difference between fascia, soffit and edge metal that lasts and fascia, soffit and edge metal that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with cast-iron drain bowls with replacement clamping rings, tapered polyisocyanurate laid to a quarter-inch board layout, lead-lined through-wall scupper sleeves, torch-applied SBS cap sheet turned up the parapet, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Yonkers job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. Years of roofing work in southwest Westchester means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do fascia, soffit and edge metal outside Yonkers
Yonkers Roof Pros covers Yonkers and the surrounding communities of southwest Westchester. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Fascia, Soffit and Edge Metal in Mount Vernon, NY — Westchester County, population 73,893
- Fascia, Soffit and Edge Metal in Bronxville, NY — Westchester County, population 6,656
- Fascia, Soffit and Edge Metal in Tuckahoe, NY — Westchester County, population 7,084
- Fascia, Soffit and Edge Metal in Eastchester, NY — Westchester County, population 20,901
- Fascia, Soffit and Edge Metal in Scarsdale, NY — Westchester County, population 18,253
- Fascia, Soffit and Edge Metal in Hartsdale, NY — Westchester County, population 3,377
Start on the Yonkers Roof Pros homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why Yonkers Chooses Yonkers Roof Pros
- ✓We settle one question before any other: does this roof still drain. The city's own re-roofing permit hangs two code allowances on that word, and your price hangs on it too.
- ✓A hose test on the low corner with the chalk line and the drain-down time written onto the estimate, rather than a slope guessed at from the sidewalk.
- ✓The drain bowl, clamping ring, strainer and the leader inside the wall chase are itemized apart from the membrane, because they fail on a completely different clock.
- ✓Where the street face is shingle and the deck behind it is membrane, you get two systems, two prices and two service lives, never one figure for the address.
The standards behind fascia, soffit and edge metal
Quality here is not a matter of opinion — it is written down. The fascia, soffit and edge metal work we do in Yonkers follows published industry standards: NRCA publishes the Roofing Manual, the industry's reference for details and slope minimums, and Asphalt Roofing Manufacturers Association sets the shingle application and ventilation guidance the warranties reference. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every fascia, soffit and edge metal project in Yonkers gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free fascia, soffit and edge metal free estimate in Yonkers, or request a quote and we'll get right back to you.